1/4″ PRE-CUT GALVANIZED STEEL CABLE

The 1/4″ Pre-cut Galvanized Steel Cable is 7 x 19 strand aircraft cable factory cut to commonly used lengths. Galvanized steel cables are the most common type of cable. Galvanized steel cable is stronger than stainless steel cable. Breaking Strength = 7,000 lbs Most commonly used cable for boat lifts. Moderate corrosion resistance & remains ductile over long periods running over sheaves. Custom cut at BH-USA.

BH-USA recommends 7 x 19 aircraft cables for boat lift applications. 7 x 19 means the rope has seven strands and there are nineteen wires in each strand. Always consider at least a 5:1 safety factor when figuring working loads. Test certificate for all cables sold by BH-USA is available upon request. Aircraft cables are not suitable for use in aircraft controls.

Available with Swaged end upon request
15'-$12, 31'-$39, 40'-$45, 62'-$65 and 100'-$129
Call 318-286-9169 to order.

5/16″ PRE-CUT GALVANIZED STEEL CABLE

The 5/16″ Pre-Cut Galvanized Steel Cable is 7 x 19 strand aircraft cable factory cut to commonly used lengths. Used on boat lifts, small diameter pulleys, sailboat rigging, winches, and control cables. Galvanized steel cable is most common type of steel cable and is stronger than stainless steel cable. Breaking Strength = 9,800 lbs

BH-USA recommends 7 x 19 aircraft cables for boat lift applications. 7 x 19 means the rope has seven strands and there are nineteen wires in each strand. Always consider at least a 5:1 safety factor when figuring working loads. Test certificate for all cables sold by BH-USA is available upon request. Aircraft cables are not suitable for use in aircraft controls.

Available with Swaged end upon request
15'-$19, 31'-$34, 40'-$42, 62'-$45 and 100'-$95
Call 318-286-9169 to order.

1/4″ PRE-CUT 316 STAINLESS STEEL CABLE

The 1/4″ Pre-Cut 316 Stainless Steel Cable is factory cut 7 x 19 strand aircraft cable commonly used on boat lifts, small diameter pulleys, sailboat rigging, winches, and control cables. 7 x 19 strand stainless steel cable is best all-around cable for most applications. Superior corrosion resistance. Strongly recommended for saltwater use. Breaking Strength = 6,400 lbs

7 x 19 means the rope has seven strands and there are nineteen wires in each strand. Always consider at least a 5:1 safety factor when figuring working loads. We offer test certificate for all cables sold by BH-USA. The certificates are available upon request. Aircraft cables are also not suitable for use in aircraft controls.

Available with Swaged end upon request
15'-$29, 31'-$45, 40'-$59, 62'-$80 and 100'-$179
Call 318-286-9169 to order.

5/16″ PRE-CUT 316 STAINLESS STEEL CABLE

The 5/16″ Pre-Cut 316 Stainless Steel Cable is factory cut 7 x 19 strand aircraft cable commonly used on boat lifts, small diameter pulleys, sailboat rigging, winches, and control cables. 7 x 19 strand stainless steel cable is best all-around cable for most applications. Superior corrosion resistance. Strongly recommended for saltwater use. Breaking Strength = 9,000 lbs

7 x 19 means the rope has seven strands and there are nineteen wires in each strand. Always consider at least a 5:1 safety factor when figuring working loads. We offer test certificate for all cables sold by BH-USA. The certificates are available upon request. Aircraft cables are also not suitable for use in aircraft controls.

Available with Swaged end upon request
15'-$25, 31'-$64, 40'-$79, 62'-$119 and 100'-$219
Call 318-286-9169 to order.

1/4″ DROP FORGED WIRE ROPE CLIP

The 1/4″ Drop Forged Wire Rope Clip are drop forged from a single piece of galvanized steel and are not cast. Preferred clips of riggers. Strongest available clip to use with heavy or suspended loads. The clips come in a variety of sizes. A wire rope clip ,sometimes called a u-bolt clamp or u-bolt clip, is used to clamp the loose end of a length of wire rope, once it has been looped back to form an eye. These fittings consist of a u-bolt and have a saddle secured by two nuts.

5/16″ DROP FORGED WIRE ROPE CLIP

The 5/16″ Drop Forged Wire Rope Clip are drop forged from a single piece of galvanized steel and are not cast. Preferred clips of riggers. Strongest available clip to use with heavy or suspended loads. The clips come in a variety of sizes. A wire rope clip ,sometimes called a u-bolt clamp or u-bolt clip, is used to clamp the loose end of a length of wire rope, once it has been looped back to form an eye. These fittings consist of a u-bolt and have a saddle secured by two nuts.

1/4″ STAINLESS DROP FORGED WIRE ROPE CLIP

The 1/4″ Stainless Drop Forged Wire Rope Clip is used to secure the ends of wire rope. Made from a single piece for steel and not cast making these the preferred clips of riggers. Strongest available clip for use with heavy loads and suspended loads. BH-USA recommends 7 x 19 aircraft cable for boat lift applications. 7 x 19 means the rope has seven strands and also there are nineteen wires in each strand. Always consider at least a 5:1 safety factor when figuring working loads. Test certificate for all cable sold by BH-USA is also available upon request. Aircraft cable is also not suitable for use in aircraft controls.

5/16″ STAINLESS DROP FORGED WIRE ROPE CLIP

The 5/16″ Stainless Drop Forged Wire Rope Clip is used to secure the ends of wire rope. Made from a single piece for steel and not cast making these the preferred clips of riggers. Strongest available clip for use with heavy loads and suspended loads. BH-USA recommends 7 x 19 aircraft cable for boat lift applications. 7 x 19 means the rope has seven strands and also there are nineteen wires in each strand. Always consider at least a 5:1 safety factor when figuring working loads. Test certificate for all cable sold by BH-USA is also available upon request. Aircraft cable is also not suitable for use in aircraft controls.

$45 for a set of 8
PN 75658
Call 318-286-9169 to order.

1/4″ GALVANIZED WIRE ROPE THIMBLE

The 1/4″ Galvanized Wire Rope Thimble go inside cable loop to protect cable from shafting, cutting or crimping when attaching to items that could damage the cable. BH-USA recommends 7 x 19 aircraft cable for boat lift applications. 7 x 19 means the rope has seven strands and there are nineteen wires in each strand. Always consider at least a 5:1 safety factor when figuring working loads. Test certificate for all cable sold by BH-USA are also available upon request. Also, Aircraft cable is not suitable for use in aircraft controls.

$4 for a set of 4
PN 70133
Call 318-286-9169 to order.

5/16″ GALVANIZED WIRE ROPE THIMBLE

5/16″ Galvanized Wire Rope Thimble go inside cable loop to protect cable from shafting, cutting or crimping when attaching to items that could damage the cable. BH-USA recommends 7 x 19 aircraft cable for boat lift applications. 7 x 19 means the rope has seven strands and there are nineteen wires in each strand. Always consider at least a 5:1 safety factor when figuring working loads. Test certificate for all cable sold by BH-USA are also available upon request. Also, Aircraft cable is not suitable for use in aircraft controls.

$4 for a set of 4
PN 70136
Call 318-286-9169 to order.

1/4″ STAINLESS WIRE ROPE THIMBLE

The 1/4″ Stainless Wire Rope Thimble go inside cable loop to protect the cable from shafting, cutting or crimping when attaching to items that could damage the cable. BH-USA recommends 7 x 19 aircraft cable for boat lift applications. 7 x 19 means the rope has seven strands and there are nineteen wires in each strand. Always consider at least a 5:1 safety factor when figuring working loads. Test certificate for all cable sold by BH-USA is also available upon request. Aircraft cable is also not suitable for use in aircraft controls

$6.00 for a set of 4
PN 70142
Call 318-286-9169 to order.

5/16″ STAINLESS WIRE ROPE THIMBLE

The 5/16″ Stainless Wire Rope Thimble go inside cable loop to protect the cable from shafting, cutting or crimping when attaching to items that could damage the cable. BH-USA recommends 7 x 19 aircraft cable for boat lift applications. 7 x 19 means the rope has seven strands and there are nineteen wires in each strand. Always consider at least a 5:1 safety factor when figuring working loads. Test certificate for all cable sold by BH-USA is also available upon request. Aircraft cable is also not suitable for use in aircraft controls.

$12 for a set of 4
PN 70145
Call 318-286-9169 to order.

1.5 TON GALVANIZED SHACKLE

The 7/16″ 1.5 Ton Galvanized Shackle are a screw pin shackle with raised stamp rating. Galvanized per ASTM A153 standards with a heat treated screw pin. Hot dipped galvanized alloy steel screw pin shackles. Designed for frequent removal. Permanently marked with size and working load limit (WLL), in tons. Made of forged steel then hot dipped galvanized. Weighs .4 pounds. Measures 2 1/4″ x 2 3/4″ x 2 3/4″.

$2.25 each
PN 33856
Call 318-286-9169 to order.

1/2″ 2 TON GALVANIZED SHACKLE

The 1/2″ 2 Ton Galvanized Shackle has a screw pin and has a raised stamp rating.  Galvanized per ASTM A153 standards with a heat treated screw pin. The 1/2″ galvanized shackles also have an alloy steel screw pin shackles are designed for applications where the shackle is removed frequently.  Permanently marked with size and working load limit (WLL), in tons. Working load limit of 4,000 pounds.

$3.50 each
PN 33855
Call 318-286-9169 to order.

5/8″ 3.25 TON GALVANIZED SHACKLE

The 5/8″ 3.25 Ton Galvanized Shackle has a screw pin and has a raised stamp rating. Galvanized per ASTM A153 standards. Comes with a heat treated screw pin. The galvanized shackles have an alloy steel screw pin shackles. The pin is also designed for applications where the shackle is removed frequently. Permanently marked with size and working load limit in tons. (WLL)

$8.25 each
PN 09099
 Call 318-286-9169 to order.